Shop

Showing 61–72 of 239 results

CGR – Cilinders, Load Return With Safety Nut – Low Profile

Features

Pancake lock ring cylinders have a system which prevents any possible over-stroke. The rod on these cylinders has a coloured area which appears 10mm before the maximum stroke has been reached. This version does not conform to ANSI B30.1.

These cylinders are particularly suitable for applications in which the load has to be left in a raised position for long periods. The threaded safety nut, which blocks mechanically the cylinder boby, allows to operate in total safety under the load.
All cylinders are supplied with integrated tilt saddle and eyelets in order to ease their transport .

OPERATIONAL AREAS

CGR cylinders are suggested in the construction and maintenance of bridges, viaducts, building and industrial sites where the working space is limited. The protective nitriding treatment on these cylinders gives them excellent resistance to corrosion making them suitable for use in adverse environments.

STANDARD
– Integrated tilt saddle, reduces the effects of possible off-centred loads.

Read more
CGS#D – Cylinders, Load Return Telescopic Double Stroke

Features

The hydraulic telescopic cylinders CGS are an efficient solution when you have very little space available below the load and when a long stroke is required. They can be manufactured with double stroke (D) or with triple stroke (T).

Given the high expansion only the 3% of maximum side load is allowed.

OPERATIONAL AREAS

This type of cylinder has various applications, especially in lifting of machineries but it’s considered very handy in areas with restricted space.

Read more
CGS#N – Cylinders, Load Return Standard – For High Tonnage

Features

CGS cylinders also have concentric grooves machined into the end of the rod to improve load grip, models above 30 tonne have lifting eyelets to facilitate their transport. From 50 ton upwards, the cylinders are plunging type (P version) and have a system which prevents any possible over-stroke. The rod has a coloured zone which becomes visible 10 mm before the end of the piston stroke.
All models can operate with off-centred load up to 8% of their nominal capacity.

OPERATIONAL AREAS

These hydraulic cylinders are extremely solid and are recommended for the lifting, lowering and sustaining of a heavy load.
They are carried out specifically strong in order to be usefull in applications which require very heavy loads to be lifted.
The anti-corrosion treatment applied to these cylinders makes them suitable for use in harsh and adverse environments.

OPTIONS:

– T version, cylinder with integrated tilt saddle.
– F version, cylinder with base mounting holes for fixing purposes.
– N version, (optional starting from 50 t) cylinders with end of stroke ring nut.

This version is in compliance with ANSI B30.1.

ACCESSORIES :

– ZTT tilt saddle reduces the effects of any possible off-centred load.

Read more
CGS#P – Cylinders, Load Return Standard – For High Tonnage

Features

CGS cylinders also have concentric grooves machined into the end of the rod to improve load grip, models above 30 tonne have lifting eyelets to facilitate their transport. From 50 ton upwards, the cylinders are plunging type (P version) and have a system which prevents any possible over-stroke. The rod has a coloured zone which becomes visible 10 mm before the end of the piston stroke.
All models can operate with off-centred load up to 8% of their nominal capacity.

OPERATIONAL AREAS

These hydraulic cylinders are extremely solid and are recommended for the lifting, lowering and sustaining of a heavy load.
They are carried out specifically strong in order to be usefull in applications which require very heavy loads to be lifted.
The anti-corrosion treatment applied to these cylinders makes them suitable for use in harsh and adverse environments.

OPTIONS:
– T version, cylinder with integrated tilt saddle.
– F version, cylinder with base mounting holes for fixing purposes.
– N version, (optional starting from 50 t) cylinders with end of stroke ring nut.

This version is in compliance with ANSI B30.1.

ACCESSORIES :
– ZTT tilt saddle reduces the effects of any possible off-centred load.

Read more
CGS#T – Cylinders, Load Return Telescopic Triple Stroke

Features

The hydraulic telescopic cylinders CGS are an efficient solution when you have very little space available below the load and when a long stroke is required. They can be manufactured with double stroke (D) or with triple stroke (T).
Given the high expansion only the 3% of maximum side load is allowed.

OPERATIONAL AREAS

This type of cylinder has various applications, especially in lifting of machineries but it’s considered very handy in areas with restricted space.

Read more
CMC – Extra Flat Cylinders – Spring Return

Features

The CMC range of cylinders have grooved end rods to improve the load grip, models over 20 tonne also have two threaded holes in the end rod to facilitate the screwing of the tilt saddle. All models have two holes which allows the cylinder to be bolted down onto a work surface; their flat sides also allow them to be used horizontally. Models over 5 tonne are fitted with a wiper seal and from 75 tonne upwards they are fitted with a removeable carrying handle. The CMC5N6 model is supplied with a K71F coupler (1/4” NPT connection).

OPERATIONAL AREAS

These extra compact lightweight cylinders are the ideal solution to operate in the narrowest working areas. They are used for the lifting of machineries, transformers and bridge sections while in the ship building industry can be used to raise engines into position and remove propellers.

ACCESSORIES:
– ZTT tilt saddle reduces the effects of any possible off-centred load.

STANDARD:
-Tilt saddle mounting holes.

Read more
CMF#L – Steel Hollow Piston Cylinders Spring Return

Features

All the CMF cylinder series are supplied with a smooth hollow saddle and the cylinder body, rod and bottom are threaded to facilitate the fixing and fitting of eventual accessories. The end of stroke nut has a wiper seal which prevents the penetration of dirt inside the cylinder. Cylinders are supplied with anti-corrosive treatment which is very effective to protect the central bore.

OPERATIONAL AREAS

These cylinders are recommended for tensioning and for the extractiong of pulleys, bushes and heat exchangers.They can also be used in both pulling and pushing operations by inserting either a bar or a cable through the hollow saddle. These cylinders are also supplied with the UE pullers

ACCESSORIES:
– ZTE threaded saddle Allows the fitting of threaded bars usually for extractors (UEC / UEG / UEZ / UET series).

STANDARD:
– Smooth hollow saddle prevents any risk of any possible rod deformation.

OPTIONS:
– L version, cylinders with aluminium body ( CMF###L### )

Read more
CMF#N – Steel Hollow Piston Cylinders Spring Return

Features

All the CMF cylinder series are supplied with a smooth hollow saddle and the cylinder body, rod and bottom are threaded to facilitate the fixing and fitting of eventual accessories. The end of stroke nut has a wiper seal which prevents the penetration of dirt inside the cylinder. Cylinders are supplied with anti-corrosive treatment which is very effective to protect the central bore.

OPERATIONAL AREAS

These cylinders are recommended for tensioning and for the extractiong of pulleys, bushes and heat exchangers.They can also be used in both pulling and pushing operations by inserting either a bar or a cable through the hollow saddle. These cylinders are also supplied with the UE pullers

ACCESSORIES:
– ZTE threaded saddle Allows the fitting of threaded bars usually for extractors (UEC / UEG / UEZ / UET series).

STANDARD:
– Smooth hollow saddle prevents any risk of any possible rod deformation.

OPTIONS:
– L version, cylinders with aluminium body ( CMF###L### )

Read more
CMF#NJ – Spring Return Cylinders With Hollow Piston For Barriers Type New Jersey And Guard-rails

Features

INTRODUCTION AND OPERATIONAL AREAS

The Europress system model CMF22N8S##NJ is used to verify and test the studs in New Jersey barriers and guard rails. The barriers both New Jersey, steel or concrete, and the guard rails are fixed to the road thanks to studs which generally have M16, M20 or M24 dimensions. Both during the installation and the exercise of the studs it’s necessary to verify them through traction tests in order to prove their adherence to concrete and the integrity of the material. To this purpose the Europress system allows to fulfill simple and efficient tensile strength tests. The system is composed of a traction load cell CMF22N8G constituted by a simple effect spring return hollow ram cylinder, with a nominal capacity of a maximum of 212 kN at 700 bars, 8 mm of stroke, firmly connected to a gauge and provided with a quick female coupler combined with a pump which generates hydraulic pressure. This traction cell constitutes an instrument to measure the force applied on the stud while testing. If calibrated as a measurement instrument it can be used also to redact calibration certificated tests. Depending on the different applications required the set can be equipped with ancillaries which are useful to the traction of studs of M16, M20, M24 diameter. Moreover it can be used a longer M20 diameter version for the traction of studs fixed on steel New Jersey barriers. The cylinder is activated by a PNP130 (or PN131) hand pump and a flexible hose SN20M with a male coupler on top.The pump is connected thanks to the male coupler fixed on one side of the hose which is connected to the female coupler fixed on the cylinder. The hollow ram cylinder, thanks to its through hole, allows the passage of the tie-rod of appropriate dimension in order to screw it on the stud itself. Extending the piston of the cylinder, a tensile force, proportional to the pressure generated by the pump, is exerted on the stud. The gauge allows at last to verify and control the force exerted on the stud.

Read more
CMI#N – Multi-purpose Cylinders, Spring Return With Metric Thread

Features

All the CMI cylinders have collar threads on the cylinder body and mounting holes in the base. They are supplied with an interchangeable grooved pushing saddle and models above 30 tonne are supplied with a handle for the carrying. A wiper seal is fitted on models above 5 tonne to prevent the penetration of dirt and to extend the life of the cylinder.

OPERATIONAL AREAS

These cylinders can be operated in any position and are extremely versatile and suitable for different applications, including industrial works, steel structural works, presses and special applications. The nitride treatment gives these cylinders an excellent resistance to corrosion and makes them particularly suitable to operate in the open air or in aggressive environments.

ACCESSORIES :
– ZTT tilt saddle reduces the effects of any possible off-centred load.
– Base plates. ZAB
– Clevis eyes. ZAR and ZAE

STANDARD :
– Base mounting holes.
– Pushing saddle prevents any risk of rod deformation.

Read more
CMI#W – Multi-purpose Cylinders, Spring Return With Imperial Thread

Features

All the CMI cylinders have collar threads on the cylinder body and mounting holes in the base. They are supplied with an interchangeable grooved pushing saddle and models above 30 tonne are supplied with a handle for the carrying. A wiper seal is fitted on models above 5 tonne to prevent the penetration of dirt and to extend the life of the cylinder.

OPERATIONAL AREAS

These cylinders can be operated in any position and are extremely versatile and suitable for different applications, including industrial works, steel structural works, presses and special applications. The nitride treatment gives these cylinders an excellent resistance to corrosion and makes them particularly suitable to operate in the open air or in aggressive environments.

ACCESSORIES :
– ZTT tilt saddle reduces the effects of any possible off-centred load.
– Base plates. ZAB
– Clevis eyes. ZAR and ZAE

STANDARD :
– Base mounting holes.
– Pushing saddle prevents any risk of rod deformation.

Read more
CML – Spring Return Aluminium Cylinders

Features

Five models of this type of cylinder are manufactured in a high resistance aluminium cylinder body (and end of stroke nut for 100 tonne) with a protective treatment, to increase the resistance to corrosion. Wiper seals are fitted to prevent the penetration of dirt. It’s recommended to carefully avoid, despite the protective treatment, the eventual flow of water which, due to the galvanic currents, can deteriorate the surface. Given the sensitivity of the material to work stress we suggest a maximum use of 5000 work cycles. All models are supplied with interchangeable grooved pushing saddle and have two lateral threaded holes to enable the mounting of a tilt saddle to reduce the effects of any side loading.

They are also fitted with a removable carry handle.

OPERATIONAL AREAS

Because of their extremely low weight and dimensions these cylinders are particularly suitable for use in applications where lightness and ease of handling are paramount.

ACCESSORIES :
– Separate ZTT tilt saddle reduces the effects of possible off-centre loads.

STANDARD :
– Pushing saddle prevents any risk of rod deformation.

Read more