Shop

Showing 157–168 of 239 results

  • PN – Lightweight Alloy Hand Pumps

    Features

    The main quality of PN is the lightness (their weight is over 50% less compared to traditional products). They are made from light alloy metal which is normally used in the aviation field due to its mechanical resistance. Because of this, PN pumps are extremely handy and stand out due to a very low effort on their handle. The practical pedal locking hook allows to use the lever as a handle during transport by holding it in the correct position in order to balance the pump correctly even if equipped with ancillaries. The pumps with 1 and 2 liter oil tank have a brand new design and a bigger internal usable oil volume. This allows both to use the total internal capacity without opening the oil briefer cap or to fill the tank completely in order to use, with the cap in briefing position, a much bigger quantity of oil.

    All 700 bar models have:

    – Externally adjustable relief valve ;
    – Side port 1/4” NPT for the direct fitting of the G106L gauge ( PN26# range excluded) ;
    – 1/4” NPT hole to insert directly the G106 gauge only on the PN46# pump
    – Fixing holes ;
    – Tank from 1,2 – 2,2 – 4,3 e 7,8 lt.

    All 1000 / 1600 / 2800 / 4000 bar models have:

    – Double stage (except PN13110/16/28 and PN13110 models);
    – Externally adjustable low and high pressure relief valves ;
    – Second port (also usable as gauge port) only on PN13110/16/28, PN16#28 and PN13240 models;
    – Fixing holes ;
    – Tank from 1,2 – 2,2 – 4,3 e 7,8 lt.

    All PN pumps can work vertically with the pumping head pointing downwards.
    For a proper
    They can be fastened by using the ZPN#MOD kit.
    The usable oil volume is 100% of the reservoir capacity with 1 and 2 litre tanks, thanks to the filler cap positioned at the end of the tank.

    OPERATIONAL AREAS

    – PN13# Series Single stage pumps with 1,2 – 2,2 litre reservoirs, for single acting cylinders with short strokes and small/medium oil capacities.
    – PN14# Series Double stage pumps with 1,2 – 2,2 litre reservoirs with a pressure relief valve on the first stage, recommended for single acting cylinders with medium strokes and medium oil capacities.
    – PN16# Series Double stage pumps with 2,2 – 4,3 – 7,8 litre reservoirs with unloading valve to facilitate the pumping on the second stage; recommended for single acting cylinders with long strokes and large oil capacities.
    – PN26# Series Double stage pumps with 2,2 – 4,3 – 7,8 litre reservoirs with unloading valve to facilitate the pumping on the second stage; with a 4 way valve, for double acting cylinders with long strokes and large oil capacities.
    – PN46# Series Pumps like the PN26# series but equipped with an additional pilot check valve in order to maintain the load while moving the lever and to control the lowering of the cylinder under load.
    – PN13110 – PN16#10 series Used in extracting operations, in lab tests and to operate hydraulic bolt tensioners models UTN and UTH.
    – PN13116 – PN16#16 Series Used in all bearings extractions and to operate hydraulic bolt UTV tensioners.
    – PN13128 – PN16#28 – PN13240 Series They are most useful and effective in cases of laddering of bearings, in tightenings, in pretensioning of studs, in burst tests and in calibrations.

  • Pneumatic Piston Grease Pump, Pumpmaster 35, Pm35 – 60:1, 185 Kg (400 Lb) Drums, Npt

    Technical Data

    Maximum free flow delivery (SI) 2 kg/min, 4.4 lb/min, 2 kg/min
    Air motor effective diameter 80 mm (3.15 “)
    Delivery per cycle 900 g/min (2 lb)
    Maximum outlet pressure 600 bar (8700 psi)
    Total height 1212 mm (47.7 “)
    Air consumption 450 NL/min (15.9 scfm)
    Air pressure operating range 2 – 10 bar (29 – 145 psi)
    Air inlet 3/8″ NPT (F)
    Fluids Grease
    Wetted materials Viton, PTFE, Hard chromed steel, NBR, Cast iron, Steel, UHMWPE
    Cycles per litre (aprox.) 80 cycles
    Pump mounting 185 kg (400 lb) drums
    Fluid outlet 3/8″ NPT (F)
    Fluid inlet type Chop-check
    Noise level 80 dB
    Weight 11 kg (24.2 lb)
    Fluid inlet
    Pressure ratio 60:1
    Delivery 900 g/min (2 lb/min)
    Air motor stroke 80 mm (3.15 “)
    Tube height 925 mm (36.4 “)
  • Pneumatic Piston Oil Pump, Pumpmaster 35, Pm35 – 5:1, Stub, Npt

    Total height 469 mm (18.5 “)
    Air pressure operating range 2 – 12 bar (29 – 174 psi)
    Delivery per cycle 12 l (3.2 gal)
    Wetted materials Hard chromed steel, Steel, Polyurethane, NBR, Aluminium
    Air motor stroke 80 mm (3.15 “)
    Air motor effective diameter 80 mm (3.15 “)
    Fluid inlet 1 1/2″ NPT (F)
    Maximum free flow delivery (SI) 30 l/min, 8 gal/min, 30 l/min
    Air consumption 350 NL/min (12.4 scfm)
    Fluid inlet type Ball check
    Fluids Hydraulic oil, Gear oil, Lubricant oil, Transmission fluid
    Pump mounting Universal stub pump
    Cycles per litre (aprox.) 80 cycles
    Weight 5.3 kg (11.7 lb)
    Fluid outlet 1/2″ NPT (F)
    Delivery 12 l/min (3.2 gal/min)
    Noise level 80 dB
    Maximum outlet pressure 60 bar (870 psi)
    Tube height 200 mm (7.9 “)
    Air inlet 3/8″ NPT (F)
    Pressure ratio 5:1
  • Pneumatic Piston Oil Pump, Pumpmaster 35, Pm35 – 8:1, Stub With Adaptor, Npt

    Technical Data

    Fluids Corrosion protection fluids, Lubricant oil, Hydraulic oil, Gear oil, Transmission fluid
    Noise level 80 dB
    Fluid inlet type Ball check
    Air inlet 3/8″ NPT (F)
    Pressure ratio 8:1
    Air pressure operating range 2 – 12 bar (29 – 174 psi)
    Maximum free flow delivery (SI) 17 l/min, 4.5 gal/min, 17 l/min
    Cycles per litre (aprox.) 80 cycles
    Air motor stroke 80 mm (3.15 “)
    Air motor effective diameter 80 mm (3.15 “)
    Delivery 7 l/min (1.9 gal/min)
    Pump mounting Universal stub pump with bung adaptor
    Maximum outlet pressure 96 bar (1392 psi)
    Fluid inlet 1″ NPT (F)
    Wetted materials Hard chromed steel, NBR, Polyurethane, Cast iron, Steel
    Fluid outlet 1/2″ NPT (F)
    Total height 487 mm (19 “)
    Delivery per cycle 7 l (1.9 gal)
    Weight 6.8 kg (15 lb)
    Air consumption 350 NL/min (12.4 scfm)
    Tube height 200 mm (7.9 “)
  • Pneumatic Piston Oil Pump, Pumpmaster 60, Pm60 – 6:1, Stub, Npt

    Technical Data

    Air motor stroke 100 mm (4 “)
    Fluids Hydraulic oil, Lubricant oil, Transmission fluid, Gear oil
    Air consumption 1100 NL/min (38.8 scfm)
    Weight 19 kg (42 lb)
    Cycles per litre (aprox.) 60 cycles
    Noise level 80 dB
    Maximum free flow delivery (SI) 100 l/min, 100 l/min, 26.4 gal/min
    Wetted materials NBR, Polyurethane, Nickel, Cast iron, Aluminium, Steel
    Delivery per cycle 35 l (9.25 gal)
    Fluid outlet 3/4″ NPT (F)
    Maximum outlet pressure 72 bar (1044 psi)
    Pressure ratio 6:1
    Delivery 35 l/min (9.2 gal/min)
    Fluid inlet type Ball check
    Air pressure operating range 1.5 – 12 bar (21.75 – 174 psi)
    Air inlet 1/2″ NPT (F)
    Air motor effective diameter 150 mm (6 “)
    Total height 716 mm (28.2 “)
    Pump mounting Universal stub pump
    Tube height 200 mm (7.9 “)
    Fluid inlet 1 1/2″ NPT (F)
  • Pneumatic Pullers (Eco Series)

  • PNP – Hand Pumps With Tank In Plastic – 700 Bar

    Features

    The main feature of the PNP pumps is it’s extreme lightness given that the body of the pump is produced from extruded aluminum and the oil tank from glass reinforced nylon. The practical pedal locking hook allows the use of the lever as a handle during transport by holding it in the correct manner it will balance the pump even if equipped with ancillaries.

    All 700 bar models have:

    – Externally adjustable relief valve ;
    – 1/4 ” NPT side port for the direct fitting of the gauge ;
    – Fitting holes ;
    – Tank from 0,7 – 1,2 lt.
    – The PNP240 model pump is equipe with a 4 way valve with 3 positions for the usage of the pump with double acting cylinders.

    All PNP pumps can work vertically with the pumping head pointing downwards with a smaller oil volume than their nominal capacity.

  • fasteners

    POP Closed-End Blind Rivets

    Fast Facts:

    • Blind hole, one-sided installation capability.
    • Unique cup-shaped end configuration.
    • Seals tight, preventing passage of vapor or liquid around or through the set rivet.
    • 23% greater tensile strength than equivalent open-end rivets.
    • 100% mandrel retention.
    • Assembly applications include white goods, electronic enclosures, signs, outdoor cases, scoreboards, LED signs, and recreational vehicles.
  • fasteners

    POP Grip Tite Rivets

    Through thick and thin, Grip Tite™ rivets feature strong, vibration-resistant joints. Even with thin sheet metal or plastics, Grip Tite™ rivets will set without any material deformation. Grip Tite™ rivets provide mandrel retention and an impressive expanded footprint on the blind side. The wide blind side expansion feature can compensate for irregular holes and spread…

  • Hydraulic Pumps

    POP High-Retention (HR) Rivets

    Fast Facts:

    • Blind hole, one-sided installation capability.
    • Rib design counters deformation and stress-fracture pressures.
    • Positively retained mandrel head.
    • Excellent rattle (noise) resistance.
    • Consistent and stable clamp force.
    • Increased secondary-side expansion.
    • Assembly applications include automotive, electronic assembly, and transportation.
  • Hydraulic Pumps

    POP High-Strength (HS) Rivets

    Fast Facts:

    • Increased blind-side expansion.
    • High clamp load.
    • Vibration-resistant joints.
    • Accommodates oversized holes.
    • Positively retained mandrel head.
    • Excellent rattle (noise) resistance.
    • Grooved mandrel.
    • Optimizes jaw and tool life.
    • For use in structural applications.
  • Bolting Tools

    POP Jack-Nut Rivet Nuts

    Available in steel and brass, Jack-Nut rivet nuts can be coated with RAINTITE® to seal moisture and hard plastic PVC to prevent scratching and galvanic corrosion. Jack-Nut threaded inserts are RoHS-, ELoV-, and WEEE-compliant. Fast Facts: Fastens in blind holes Won’t distort or deform soft plastics or thin sheet metals Fast, inexpensive, and easy to use…

  • Model Number. Air Pressure
    (BAR)
    Puller Capacity (Tonne) JAW No. Max. Stroke (mm) Max Spread A (mm) Max. Reach
    B (mm)
    Thickness of
    Jaw C (mm)
    Thickness of
    Jaw Tip D (mm)
    Weight
    (kg)
    APP-5 8 5 3 50 200 140 26 11 7.3
    APP-10 8 10 3 60 250 170 30 13 10.9
    APP-20 8 20 3 70 350 205 33 18 19.2
    APP-30 8 30 3 70 400 220 35 20 25.5
    APP-50 8 50 3 60 500 250 40 25 44.2